Besa-lighting Bolla (120V Pendants) Uživatelský manuál
Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Besa-lighting Bolla (120V Pendants). Besa Lighting Bolla (120V Pendants) User Manual Uživatelská příručka
- Strana / 4
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
FIXTURE INSTALLATION GUIDE
Model T31T (1 Light Flat Canopy 120V)
T31T, Rev.6 3-09
CAUTION: Turn off power to electrical box before installing
IMPORTANT: before proceeding, retrieve the Glass Shade Installation Guide, which is included with the pendant cord set.
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
1. Carefully unpack parts. Remove the Canopy (A) from the Mounting
Plate by unscrewing the Retainer (B). Fully remove the Retainer from
the threaded nipple, then pull the canopy from the Mounting Plate.
2. If the cord length requires adjustment, simply unscrew the Set Screw
on the Strain Relief (C). Now push the cord up through the Strain Relief
until reaching the desired length. Tighten the Set Screw onto cord until
the cord is firmly held in place. To shorten the cord, cut to the desired
length then strip back the outer jacket and the inner conductors. When
shortening the cord, it is recommended that the polarity is confirmed,
per the Polarity Instructions below.
3. Install the provided Mounting Screws (D) into the Outlet Box,
leaving 1/4” of threading as shown.
4. Attach the house ground wire to the cord green stripe conductor
and bare copper lead, then secure with provided wirenut (E).
Connect the conductors from the fixture cord to the house supply
wires, white stripe to white and clear to black, and secure with
wirenuts provided (F).
NOTE:
Colored Sleeving Has Been Added To Conductors For Identification.
5. Align the circular openings of the keyhole slots (G) of the
Mounting Plate (H) with the Mounting Screws. Push the
Mounting Plate up over the Outlet Box until tight to ceiling,
then rotate the Mounting Plate Counter-clockwise and
secure with Mounting Screws.
A
B
C
IMPORTANT:
Refer to the Glass Shade Installation Guide to determine
the glass support parts that must be installed over the
Pendant Cord Set, prior to Step 2.
If using the optional 18” Decorative Cord Sleeve(s) (sold separately),
cut the sleeve(s) to the desired pendant length. Replace the Retainer
(B) with the retainer provided with the 18” Decorative Cord Sleeve.
Leave approx. 6” of cord slack to allow installation of glass shade.
CAUTION: Overtightening the set screw could pierce cord and
prevent pendant from operating.
*IMPORTANT:
When Mounting To Smaller Boxes,
It May Be Necessary To Secure
Using These Mounting Holes.
D
F
E
G
Green
Stripe
White
Stripe
H
Clear
Shrnutí obsahu
Strany 1 - FIXTURE INSTALLATION GUIDE
FIXTURE INSTALLATION GUIDEModel T31T (1 Light Flat Canopy 120V)T31T, Rev.6 3-09CAUTION: Turn off power to electrical box before installingIMPORTANT:
Strany 2 - POLARITY INSTRUCTIONS
FIXTURE INSTALLATION GUIDEAll electrical connections and the installation of this fixture must be in agreement with local codes, ordinances or the NEC
Strany 3
GLASS SHADE INSTALLATION GUIDEModel B Series -04 (E12 Base Pendant Set 120V) Q Series -04 (G9 Base Pendant Set 120V)BKIT.04, Rev.10 12-1166
Strany 4 - GLASS SHADE LEVELING GUIDE
All electrical connections and the installation of this fixture must be in agreement with local codes, ordinances or the NEC (National Electric Code)
Související produkty a manuály pro Osvětlení Besa-lighting Bolla (120V Pendants)
(2 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.159 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce